mrcory
cdda239b04
LED (PWM) can now be controlled with Home Assistant. Set desired brightness in the config.
138 lines
4.1 KiB
C
138 lines
4.1 KiB
C
//Config stuff
|
|
|
|
//Friendly Name
|
|
#define deviceName "Roller_Shade"
|
|
#define deviceNameLED "Roller_Shade_LED"
|
|
|
|
//Uncomment to enable wifi manager
|
|
#define wifiManagerEnable
|
|
|
|
//Enable Blynk (Old Version)
|
|
#define Blynkenable
|
|
#define rtcBlynk false
|
|
|
|
//Enable Home Assistant Integration (Displays as a fan)
|
|
//Only Supports the shade and not light control
|
|
#define HAenable
|
|
|
|
// Unique ID must be set!
|
|
byte mac[] = {0x13, 0x10, 0xFA, 0x6E, 0x38, 0x4A};
|
|
|
|
//Home Assistant Config
|
|
#define brokerAddress IPAddress(192,168,254,84) //MQTT Broker Address
|
|
#define brokerUser "user" //Broker Username
|
|
#define brokerPass "password" //Broker Password
|
|
|
|
/* Speed Settings in Steps/Second
|
|
* You will have to play with these values to find a
|
|
* reliable setup. I recomend putting a small extra load
|
|
* (lightly pressing a finger against the roller) to
|
|
* be sure that there is enough strength to lift the shade
|
|
* reliably.
|
|
*
|
|
* .! This is used for both motor types !.
|
|
*/
|
|
|
|
motorSpeedStruct mSpeed = {
|
|
800, //Up Speed
|
|
1000, //Down Speed
|
|
150 //Acceleration
|
|
};
|
|
|
|
|
|
|
|
/* Drive motor selection.
|
|
* You have choice between 2 style motors.
|
|
*
|
|
* 28BYJ-48 : 5v or 12v | Though slow, these motors are cheap.
|
|
* The 5v has the advantage of being able to receive power from a
|
|
* power bank. This could allow operation when your electricity goes out.
|
|
*
|
|
* Nema 17 : 12v | This motor should be faster, but will require a
|
|
* brake or to remain powered to hold its position.
|
|
*
|
|
* 28BYJ will be controlled by steps, while Nema will be controlled by degrees.
|
|
*
|
|
* Uncomment the appropriate line below. Edit the config at the top of selected.
|
|
*/
|
|
#include "stepperMini.h"
|
|
//#include "stepperNema.h"
|
|
|
|
int connectTimeout = 100; // How many attempts can we make before giving up on Blynk
|
|
//#define blynkRtcInterval = 30; // How often to sync the time. (Would be used for timers)
|
|
|
|
#ifdef Blynkenable
|
|
#include "blynk.h" //Contains Blynk login
|
|
#endif
|
|
|
|
//------Timer
|
|
int stepperPos[] = {0,6000};
|
|
int stepperTime[2][2] = {};
|
|
//------Not currently used
|
|
|
|
/* Set size for the eeprom.
|
|
* 512 is way more than will be needed.
|
|
* All that is being stored there is position data
|
|
* after each move is completed.
|
|
*/
|
|
const int eepromSize = 512;
|
|
|
|
|
|
|
|
//Button Config
|
|
#define buttonEnable true //True to enable button controls
|
|
#define buttonPin A0 //Analog pin for buttons
|
|
|
|
//AnalogRead values for buttons
|
|
#define upVal 895
|
|
#define dnVal 980
|
|
#define rsVal 1024
|
|
|
|
/* The margin that analogButtons uses to determine
|
|
* if a button has been pressed. Default is 20, but
|
|
* I use 30. As long as there is plenty of gap between
|
|
* values set above, this can be set larger.
|
|
*/
|
|
#define buttonMargin 30
|
|
#define buttonDebounce 3 //Debounce for buttons. Lower causes faster trigger.
|
|
#define ANALOGBUTTONS_SAMPLING_INTERVAL 10
|
|
|
|
//Feedback for button presses
|
|
#define ledPin D3 //Feedback LED
|
|
|
|
/* This will allow control of an accessory light via
|
|
* PWM or FastLED.
|
|
* If using FastLED controlled lights, be careful of
|
|
* the number you use. Always calcualte the max possible
|
|
* power consumption and add a safety margin.
|
|
*/
|
|
#define alternateFunction false //Enable alternate use of the reset button
|
|
#define lightMode 0 //0-PWM 1-FastLED
|
|
|
|
/* Light accessory settings (Not the feedback LED)
|
|
* Using FastLED to run some WS2812
|
|
* The data pin for the WS2812 is set in the main ino
|
|
* around line 31
|
|
*/
|
|
int ledBrightness = 900; //Starting brightness
|
|
int ledButtonBrightness = 50; //Brightness to use when using rst button to turn on light.
|
|
int pulseMax = 250; //Max brightness for pulse mode. Max 250 or it will loop to near 0
|
|
//Can be set in Blynk
|
|
|
|
//FastLED Settings
|
|
#define NUM_LEDS 9 //Number of attached LEDs
|
|
#define DATA_PIN D2 //Communication pin for the LEDs | Same pin will be used for either LED control
|
|
#define LED_TYPE WS2812 //LED controller
|
|
#define COLOR_ORDER GRB //Order to send colors
|
|
|
|
//PWM Light Settings
|
|
#define PWM_PIN D2 //Rev.0 PCB uses D2
|
|
|
|
|
|
//Extra Stuff
|
|
#define cmds true //After setting up positions, cmdArduino can be disabled
|
|
|
|
//OTA Settings
|
|
#define updatePassword "admin"
|
|
#define myHostName "Shade"
|